View LSP3308AQAC_8150140.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

liteon semiconductor corporation lsp3308a 6 channels led boost driver ev1.0 1/12 0 20 40 60 80 100 16 20 24 28 32 36 40 output voltage (v) max output current (ma ) vin=12v vin=6v typical usage curve (top view) typical application white or rgb backlighting for lcd tv, lcd monitor, notebook, handy terminals, and avionics displays panels led lighting devices high power led driver general description the lsp3308a is a high-efficiency boost type led driver. it is designed for large lcd panel that employs an array o f leds as back light source. the lsp3308a employs a cu rrent-mode step-up onverter that drives six parallel st rings of leds connected in multiple series. this built-in string current-control circuit achieves 1% typical betw een strings, which ensures even brightness for all leds. separate feedback loops limit the output voltage if one or more leds open or short. the lsp3308a has features cycle-by-cycle current limit to provide consistent operation and soft-start capability. a thermal-shutdown circuit provides another level of protection. the lsp3308a has a wide +4.8v to +28v input voltage range and provides adjustable full-scale led current. features six constant-current output channels (io=40ma each @ vin=12v; io=30ma each @ vin=5v;) parallel channels allow higher current per led string maximum 40v continuous voltage output limit for each channel self-adaptive vout to fit different led number adjustable constant led current drives 10 or more leds each string as long as the string voltage less than 40v internal 2.5a power mosfet allows digital pwm and analog dimming wide (100:1) pwm dimming range without color shift independent dimming and shutdown control of the led driver open led protection: adjustable clamp voltage short led protection 3 frequencies selection: 1.6mhz/1mhz/500khz wide input voltage range: 4.8v to 28v over temperature protection available in qfn4*4-16l pb-free package pin assignment
liteon semiconductor corporation lsp3308a 6 channels led boost driver ev1.0 2/12 pin description pin number name description 1 vin supply input 2 vcc-driver 5v linear regulator output for power mos driver 3 gnd ground 4 ena enable input 5 pwmd pwm dimming control 6 led1 led1 cathode terminal 7 led2 led2 cathode terminal 8 led3 led3 cathode terminal 9 gnd ground 10 gnd ground 11 led4 led4 cathode terminal 12 led5 led5 cathode terminal 13 led6 led6 cathode terminal 14 iset led current adjustment pin 15 vcc-5v 5v linear regulator output 16 vc boost stage compensation pin 17 fsel oscillator frequency selection pin 18 fb feedback pin 19 pgnd power ground 20 pgnd power ground 21 pgnd power ground 22 sw power mos drain 23 sw power mos drain 24 sw power mos drain absolute maximum ratings (note) parameter value unit vin,ena pin vss-0.3 to vss+30 v sw,led pin vss-0.3 to vss+40 v vcc-5v,vcc-driver,vc vss-0.3 to vin + 6 v pwmd,fsel,ovp,iset. vss-0.3 to vin + 6 v power dissipation, pd internally limited mw thermal resistance(junction to case), jc 2 c/w thermal resistance(junction to environment) , ja 37 c/w junction temperature range -40 to +125 c maximum junction temperature 150 c storage temperature range, tstg -40 to +150 c soldering temperature 300(5 second) c note: do not exceed these limits to prevent damage to t he device. exposure to absolute maximum rating conditions for long periods may affect device reliability.
liteon semiconductor corporation lsp3308a 6 channels led boost driver ev1.0 3/12 electrical characteristics (v in =ena= 12v, t a = 25c,l=22uh,rset=10k ? unless otherwise specified.) parameter test conditions min. typ. max. unit input voltage 4.8 28 v ena=high (no switching) 1 ena=high (1.6m switching frequency) 10 ena=high (1m switching frequency) 6 ena=high (500k switching frequency) 3 ma quiescent current ena=low 5 20 a ldo stage vcc_5v no switching 4.7 5 5.5 v vcc_5v current_limit no switching 14 74 90 ma vcc_5v uvlo threshold no switching 3.9 4.2 4.5 v vcc_5v uvlo hysteresis no switching 70 mv vcc_driver no switching 4.7 5 5.5 v vcc_driver current_limit no switching 14 74 90 ma vcc_driver uvlo threshold no switching 3.9 4.2 4.5 v vcc_driver uvlo hysteresis no switching 70 mv boost stage feedback voltage 1.2 v switch rdson vcc_5v=5v 0.2 ? switch current limit 2.5 a switch leakage current 1 a fsel=vcc_5v 1.6 fsel=open 1.0 switching frequency fsel=gnd 0.5 mhz fsel=vcc_5v 20 fsel=open 10 minimums duty cycle fsel=gnd 5 % maximums duty cycle 90 % vc source current 60 a vc sink current 60 a led ccontroller stage i =190*1.2v/riset, riset=7.68k 30 ma i =190*1.2v/riset, riset=11.3k 20 ma full-scale led_output current i =190*1.2v/riset, riset=22.6k 10 ma led current matching -3 1 +3 % iset voltage 1.2 v minimums led voltage 400 mv analog dimming range i =190*1.2v /riset i /32 i ma pwm dimming frequency 100 1k hz fault protection led_ overvoltage threshold 4.6 4.9 5.1 v led_ overvoltage hysteresis 1 v thermal-shutdown 150
thermal-shutdown hysteresis 30
controller interface en high 1.5 v en low 0.4 v pwmd high 1.5 v pwmd low 0.4 v fsel high vcc_5v-0.5 v
liteon semiconductor corporation lsp3308a 6 channels led boost driver ev1.0 4/12 fsel midlevel 1 2 v fsel low 0.5 v en min pulse width single wire dimming low level 0.5 s en max pulse width single wire dimming low level 10 s en off delay single wire dimming low level 100 s functional block diagram
liteon semiconductor corporation lsp3308a 6 channels led boost driver ev1.0 5/12 application information inductor selection the inductance, peak current rating, series resistance, and physical size should all be considered when selecting an inductor. these factors affect the converter's operating m ode, efficiency, maximum output load capability, transient response time, output voltage ripple, and cost. the maximum output current, input voltage, output volt age, and switching frequency determine the inductor value. very high inductance minimizes the current ripple, and t herefore reduces the peak curr ent, which decreases core losses in the inductor and i r losses in the entire power pa th. however, large inductor values also require more energy storage and more turns of wire, which increases phy sical size and i r copper losses in the inductor. low inductor values decrease the physical size, but incr ease the current ripple and peak current. finding the best inductor involves the compromises among circuit efficiency, inductor size, and cost. when choosing an inductor, the first step is to determine the operating mode: continuous conduction mode (ccm) or discontinuous conduction mode (dcm). when ccm mode is chosen, the ripple current and the peak current of the inductor can be minimized. if a small-size inductor is required, dcm mode can be chosen. in dcm mode, the inductor value and size can be minimi zed but the inductor ripple current and peak current are higher than those in ccm. capacitor selection an input capacitor is required to reduce the inputrippl e and noise for proper operation of the lsp3308a. for good input decoupling, low esr(equivalent series resistance) ca pacitors should be used at the input. at least 2.2uf input capacitor is recommended for most applications. a minimum output capacitor value of 10uf is recomm ended under normal operating conditions, while a 22uf or higher capacitor may be required for higher power led curr ent. a reasonable value of the output capacitor depends on the led current. the total output voltage ripple has two components: the capacitive ripple caused by the charging and discharging on the output capacitor, and t he ohmic ripple due to the capacitor's equivalent series resistance. the esr of the output capacitor i s the import ant parameter to determine the output voltage ripple of the converter, so low esr capacitors should be used at the output to reduce the output voltage ripple. the voltage rating and temperature characteristics of the out put capacitor must also be considered. so a value of 10uf, voltage rating (50v) capacitor is chosen. diode selection lsp3308a is high switching frequency convertor, which dema nds high speed rectifier. i t ' s indispensable to use a schottky diode rated at 2a, 60v with the lsp3308a. usi ng a schottky diode with a lower forward voltage drop is better to improve the power led efficiency, and its voltage rating should be greater than the output voltage. methods for setting led current there are three methods for setting and adjusting the led current outlined here. the methods are: 1) rset 2) pwm input at pwmd 3) single wire logic signal at ena method 1: led current setting with external resistor r iset the most basic means of setting the led current is connecting a resistor between riset and gnd. the led current is decided by iset resistor. iled =228/ riset method 2: led current setting using pwm signal to pwmd pin this circuit uses resistor riset to set the on state cu rrent and the average led current, then proportional to the percentage of on-time when the pwmd pin is logic low. average led current is approximately equal to: i= ( ton*i)/ (ton + toff ) also, the recommended pwm frequency is between 100hz an d 10khz. frequency <100hz can cause the leds to blink visibly. method 3: led current setting with single wire logic to ena pin when the leds are enabled by high level, the led current initially goes to i led , dimming is done by pulsing ena low (500ns to 10 s pulse width). each pulse reduces the le d current by 1/32, so after one pulse the led current is 31/32* i led . the 32th pulse sets the led current back to i led . figure 1 shows a timing diagram for en.
liteon semiconductor corporation lsp3308a 6 channels led boost driver ev1.0 6/12 setting the output voltage the fb pin is connected to the center tap of a resistive voltage divider (r1 and r2 in typical application diagram) from the high-voltage output. v out =vfb* (1+r1/r2) the recommend procedure is to choose r2 =300k and r2 =9.2k to set v out =40v. led short protection the lsp3308a uses led_ovp function to protect dev ices when one or more led(s) is/are shorted. v led =v out ?vf*n normally is around 0.4v and is dec ided by led numbers. when one or more led(s) is/are shorted, the lsp3308a will clamp v out to make sure all led pins? voltage is less then 5v. with this function will be clamped at (5v+ vf*n min ). note: v led : led pin voltage v out : output voltage vf : led forward voltage n min : the minimum led numbers among all strings. led open protection the control loop is related to all six led sinks. when on e or more led(s) is/are opened, the sink will have no current and the device will work in unstable open loop state. the voltage will be limited by external resistor divider or 5v+ vf*n min , whichever is lower. pcb layout guidelines careful pcb layout is important for proper operati on. use the following guidelines for good pcb layout: 1) minimize the area of the high current switching loop of the rectifier diode and output capacitor to avoid excessive switching noise. 2) connect high-current input and output components with short and wide connections. the high-current input loop goes from the positive terminal of the input capacitor to the inductor, to the sw pin. the high-current output loop is from the positive terminal of the input capacito r through the inductor, rectifier diode, and positive terminal of the output capacitors, reconnecti ng between the output capacitor and input capacitor ground terminals. avoid using vias in the high-current paths. if vias are unavoidable, use multiple vias in parallel to reduce resistance and inductance. 3) create a ground island (pgnd) consisting of the input and output capacitor ground and pgnd pin. connect all these together with short, wide traces or a small ground plane. maximizing the width of the power ground traces improves efficiency and reduces output-voltage ripple and noise spikes. create an analog ground island (gnd) consisting of the output voltage detection-divider ground c onnection, the i resistor connections, vcc-5v and vcc-driver capacitor connections, and the device's ex posed backside pad. connect the gnd and pgnd islands by connecting the gnd pins directly to the exposed backside pad. make sure no other connections between these separate ground planes. 4) place the output voltage setting-divider resist ors as close to the fb pin as possible. the divider's center trace shoul d be kept short. avoid running the sensing traces near sw pin. 5) place the vin pin bypass capacitor as close to the dev ice as possible. the ground connection of the vin bypass capacitor should be connected directly to gnd pins with a wide trace. 6) minimize the size of the sw node while keeping it wide and short. keep the sw node away from the feedback node and ground. if possible, avoid running the sw node from one side of the pcb to the other. 7) refer to the lsp3308a evaluation boar d for an example of proper board layout.
liteon semiconductor corporation lsp3308a 6 channels led boost driver ev1.0 7/12 typical application circuit
liteon semiconductor corporation lsp3308a 6 channels led boost driver ev1.0 8/12 typical characteristics v in =ena= 12v, t a = 25c,l=22uh,rset=10k ? ,10*6leds
liteon semiconductor corporation lsp3308a 6 channels led boost driver ev1.0 9/12 typical characteristics (continued) typical characteristics (continued)
liteon semiconductor corporation lsp3308a 6 channels led boost driver ev1.0 10/12
liteon semiconductor corporation lsp3308a 6 channels led boost driver ev1.0 11/12 ordering information marking information
liteon semiconductor corporation lsp3308a 6 channels led boost driver ev1.0 12/12 package information

▲Up To Search▲

Price & Availability of LSP3308AQAC

	To Download LSP3308AQAC Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .